Most popular brands
Dyno chart
* This chart should be considered a visual representation only, actual values will vary.
John Deere S Series (Harvester) tractor ECU tuning and remapping for 17 supported diesel engine variants. Compare Stage 1, Stage 2 and Stage 3 power and torque gains, ECU compatibility and available tuning options.
Search 43,000+ vehicle / ECU combinations
* This chart should be considered a visual representation only, actual values will vary.
17 tuning configurations for the John Deere S Series (Harvester). Select your exact engine to see gains, options and connection details. Power gains up to +64 HP.
Alt Tune covers 17 John Deere S-Series Harvester configurations, including the S780 13.5l Tier4b, S660 9.0l 6CIL (PSX6090) Tier 3, S670 9.0l 6CIL (PSX6090) Tier 3, S680 13.5l 6CIL (PSX6013) Tier 3. Stock power spans 220 to 617 HP. Stage 1 adds up to +64 HP (+21%).
An ECU tune re-optimises the factory calibration within the standard hardware limits. On a working machine the useful change is broad, early torque for heavy draft, PTO work and hydraulics — where the load actually is.
Fuelling, boost and timing are calibrated together, with exhaust temperature and smoke kept in check. The machine is scanned before and after the write, and its original file is retained.
Power tune — more torque and pulling power at working revs for draft, PTO and hydraulic loads, calibrated within the standard hardware limits.
DPF off, EGR off and AdBlue / SCR off — cleaner running and fewer regeneration interruptions and DEF faults that cost downtime in the field.
| Engine | Stock | Tuned | Stage 1 gain |
|---|---|---|---|
| S690 13.5l Tier4b | 617 hp | 681 hp | +64 hp |
| S690 13.5l Tier3 | 617 hp | 680 hp | +63 hp |
| S540 6.8l Tier3b | 235 hp | 285 hp | +50 hp |
| S560 9.0l Tier3 | 350 hp | 390 hp | +40 hp |
| S660 9.0l Tier4b | 365 hp | 405 hp | +40 hp |
Typical gains for these engines from our tuning catalogue; exact results depend on the specific engine and its condition. Choose your generation and engine above for its stock and tuned figures.
Useful tuning is not about one peak number. It is about a machine that pulls harder at working revs and holds it through long days in the field, with less strain on the driveline.
The calibration targets the usable torque band while respecting the transmission, cooling and exhaust-temperature limits of the selected engine.
Depending on the exact engine, Stage 1 on the S-Series Harvester adds up to +64 HP (+21%). Choose your generation and engine above for its precise stock and tuned figures from our database.
We health check the vehicle first and keep a full stock backup. The calibration is built around the limits of the engine, turbo, transmission, cooling system and the condition of the vehicle.
Yes — more torque low down means the machine pulls heavier draft and runs implements and hydraulics more comfortably, often with lower fuel burn per hour and fewer regeneration interruptions in the field. Every calibration respects the engine, driveline and cooling limits.
The right route depends on the vehicle, its modifications and how it is used. A towing or work vehicle may benefit from workshop checks, while a healthy standard configuration can often be handled remotely.
The S-Series entries run from the S430 and S540 with 6.8-litre engines, through the 9.0-litre S560, S660, S670 and S770, to the 13.5-litre S680, S690 and S780. Several models are listed more than once under Tier 3, Tier 3B and Tier 4B.
Harvest leaves little room for downtime, so settle the identification in the off-season. Take the model, emission tier and your own controller read, then compare them with the listing you choose.
No. Engine size changes by model number, so the full designation, such as S660 or S690, is the starting point.
Well ahead of harvest, if you can. That leaves time to read the original controller and confirm the matching entry without pressure.
Sign in with your files.alttune.com account to unlock the advanced cable listing.